Nexsan’s InfiniSAN ATAboy2 packs ATA drives, performs like SCSI or Fibre Channel
Storage can never be fast enough, plentiful enough, or cheap enough. It used to be that the best you could hope for was two out of three. But that’s changing, thanks to advances in ATA drives and ingenuity from Nexsan Technologies. Nexsan, which started with disk-to-disk backup systems, now offers an FC (Fibre Channel) or SCSI-attached storage subsystem, the InfiniSAN ATAboy2, that uses ATA drives to provide lots of storage at very economical prices, all without any real performance penalty over a completely SCSI solution.
The InfiniSAN ATAboy2 storage subsystem is available in a desk-side tower, rack-mount, or stacking configuration. It offers 14 drives, with available 180GB or 250GB drives. The unit comes with dual power supplies, one or two SCSI or FC controllers, and a 10/100 Ethernet connection.
The Ethernet controller provides one of the unique features of the ATAboy2, which is the ability to send e-mail to a designated account if errors occur, environmental thresholds are passed, or if imminent failure is detected. The Ethernet controller also allows administrators to configure and monitor the unit via a Web browser interface.
The ATAboy2 comes with either four Ultra160 SCSI ports or two 2Gbps FC (Fibre Channel) connections; I tested a unit with SCSI ports. Redundant host connections or multiple hosts are both supported, along with up to 16 LUNs (logical unit numbers) per SCSI controller or 32 LUNs (logical unit numbers) per FC controller.
Setting up the ATAboy2 was very easy. I connected the unit to a test server via SCSI, then started the subsystem and connected it to the network. The default IP address is 10.11.12.13, which required adding a route to the network interface of the server, but that was easy enough. At that point, the unit’s Web server was fully accessible. The IP address can be reset to any other IP address or to use DHCP. The unit can also be configured via null-modem cable and a serial connection.
The ATAboy2 comes preconfigured with all drives in a single RAID 5 array, and a single partition, which is probably how most users will want it. This does mean that administrators who need any other configuration will have to delete the existing RAID set, but that is a quick and easy operation. RAID options include RAID 0, 4, and 5, with or without hot spares. Multiple RAID sets are supported, as are multiple hosts, though multiple hosts accessing the same LUN will cause problems unless additional software is used to prevent both hosts from accessing the same volume at the same time.
Other configuration options include setting an e-mail address that will receive alerts, and configuring security on the GUI interface. By default, the GUI is not password protected, so this is one of the first things the administrator should do.
After checking the unit’s configuration, I started my server and mounted the array. Testing confirmed that this is not simply an out-of-band or secondary storage unit – performance figures were very close to the best I’ve seen from a SCSI storage subsystem. Using Iometer, I found that the throughput on the SCSI controller matched Nexsan’s claims of 160Mbps burst transfer rate, 100Mbps sustained transfer rate, and 16,000 I/O operations per second.
The ATAboy2 also has good redundancy features. All the components can be easily swapped by the user, including the RAID controllers, power supplies, and drives, although the RAID controllers are not hot-swap. Removing one of the power supplies generated an alert e-mail, as did replacing it.
I also checked RAID functionality by removing and replacing a drive. The alarm sounded, an e-mail was generated, and the volume remained available. Performance was minimally degraded during the RAID-set rebuild. I was also able to create a RAID set with a hot-spare drive. When I then removed a drive from the array, the hot spare was automatically added to the set and a rebuild commenced.
The ATAboy2 delivers superb performance, as well as high capacity and good redundancy, at a bargain-basement price. Nexsan also offers an excellent three-year warranty that includes free cross-shipment of replacement parts, and an optional redundant fail-over system. This unit should be on the short list of any storage administrator who doesn’t need the absolute highest performance.
Overall Score (100%)
|Nexsan InfiniSAN ATAboy2||10.0||9.0||9.0||9.0||9.0||9.0|
You may still be better off sticking with Win7 or Win8.1, given the wide range of ongoing Win10...
With myriad problems now evident, it may be best to skip the Anniversary Update for now
An unlikely combination of two Windows updates can reduce scan times from hours to minutes
Sponsored by Hewlett Packard Enterprise
Breaches can and do happen in the cloud -- and it's usually IT's fault. Here's how to recover from one...
Pushback against municipal broadband and stalling tactics in granting access to utility poles keep...
A Java Development Kit proposal from Oracle would bring ahead-of-time compilation to the platform with...
Are you being paid what you're worth? Cloud compensation and services provider PayScale's latest IT...